Shop By BikeSetting the standard in crash protection and bolt-on motorcycle accessories.
You're viewing All Products for Ducati - Multistrada 1200
Showing 1-50 of 155 results
This 6-piece set of R&G Titanium Sprocket Nuts are made from grade 5 - 6AL-4V - 1068 MPA titanium, meaning they offer extraordinary strength and weight reduction. Our Black Titanium Sprocket Nuts go through a PVD (physical vapour deposition) treatment, ensuring longevity and corrosion resistance.
• Only use Manufacturer torque settings, between 33 - 45nm.
• Kits are offered as bike-specific fitments. If you have a variation of a standard model you may require an alternative kit. ...
These crash protectors feature our stylish, aerodynamic Aero Bobbin and are suitable for the Ducati Multistrada 1200 '15-, Multistrada 950 '17- models.
R&G Aero Bobbins are a stylish, aerodynamic, teardrop shaped bobbin improving on the original good looks of our highly successful and popular standard round bobbins. Fitted with a removable end cap which hides the bobbins fittings, this sleek design looks superb and is a winner on road and track!
R&G Aero Bobbins from R&G - the...
These crash protectors feature our stylish, aerodynamic Aero Bobbin and are suitable for the Ducati Multistrada 1200 models from 2010-2014 (NOT GT Model).R&G Aero Bobbins are a stylish, aerodynamic, teardrop shaped bobbin improving on the original good looks of our highly successful and popular standard round bobbins. Fitted with a removable end cap which hides the bobbins fittings, this sleek new design looks superb and is a winner on road and track!
Tidy up your bike's rear end with this R&G Tail Tidy/Licence Plate Holder for the Ducati Multistrada 1200!
Universal Licence plate adapters to suit different number plates hole widths, once installed enable a certain amount of flexibility when fitting the a number plate, replacing the need to redrill your number plate.
Available in a one size fits all.
Supplied in pairs.
NO TAIL TIDY BRACKET IS SUPPLIED WITH THIS KIT
Available in black, titanium or red powder coat finishes, this radiator guard fits the Ducati Multistrada 1200/S '15-, Pikes Peak '16- & 1260, 1260S, 1260 D-Air & 1260 Pikes Peak '18- models.
Made from pressed aluminum and feature a neat, seamless frame (where applicable). They improve the looks of your bike and help to protect your expensive and vulnerable radiator from flying debris.
R&G Radiator Guards are made from aluminium, improve looks and protect your expensive and vulnerable radiator from flying debris.This radiator guard is suitable for Ducati Multistrada 1200 models from 2010-2014 (Not Gran Tourismo).
This R&G Oil Cooler Guard is available in black and red finish. They are made from pressed aluminium and feature a neat, seamless frame. They improve the looks of your bike and help to protect your expensive and vulnerable oil cooler from flying debris.No permanent modifications need to be made to the bike.
This oil cooler guard is suitable for the oil cooler found in the nose cowling of the Ducati Multistrada 1200/S/Enduro '15-, Multistrada 1200S Pikes Peak '16-, Multistrada 950 '17-mo...
The R&G Stainless Steel Oil Cooler Guard series is a more rugged version of our existing aluminium guard.
Constructed from 1mm stainless steel sheet allows the guard to be incredibly strong and impervious to rust – perfect for bikes and riders who may tackle demanding terrains and conditions.
The laser-cut grills are designed for maximum airflow to the Oil Cooler so that cooling isn't compromised; the Oil Cooler Guard is as good looking as it is purposeful.
This oil c...
R&G Oil Cooler Guards are available in a powder coated Black or Red finish. They are made from pressed aluminium and feature a neat, seamless frame. They improve the looks of your bike and help to protect your expensive and vulnerable oil cooler from flying debris.No permanent modifications need to be made to the bike.This oil cooler guard is suitable for the nose mounted cooler found on the Ducati Multistrada 1200 '10-'14.
The R&G Stainless Steel Radiator Guard series is a more rugged version of our existing aluminum offering and are aimed particularly for Adventure and Touring bikes.
Constructed from 1mm stainless steel sheet allows the guard to be incredibly strong and impervious to rust – perfect for bikes and riders who may tackle demanding terrains and conditions.
The laser-cut grills are designed for maximum airflow to the radiator so that cooling isn't compromised; the Radiator Guard is ...
This model is suitable for the Ducati Multistrada 1200 2010-2014 (Not Grantourismo).
New for 2013. The R&G Stainless Steel Radiator Guard series is a more rugged version of our existing aluminium offering and are aimed particularly for Adventure bikes.
Constructed from stainless steel allows the guard to be incredibly strong and impervious to rust – perfect for bikes and riders who may tackle demanding terrains and conditions.
The laser-cut grills are designed for ma...
Available in a 16"x 12" sheet, this R&G Titanium universal mesh is both lightweight and super strong, thanks to its real Titanium (ASTM B265 Grade 1) mesh construction.
Made from the same high quality mesh found on in our Titanium radiator and oil cooler guards, it improves the looks of your bike and help to protect your expensive and vulnerable radiator and other components from flying road debris.
No permanent modifications need to be made to the bike.
Supplied with...
Dropping your cherished bike can be an expensive exercise. R&G Adventure Bars offer the rider peace of mind. R&G Adventure Bars provide essential crash protection for your motorcycle. Made from 28mm gauge steel tubing, powder coated for a strong and superbly finished product.
All R&G crash protection solutions are designed to be bike specific, therefore ensuring the best fit to your motorcycle without the need to modify.
All R&G products come supplied with comprehensive f...
Suitable for the right hand side case cover of the Ducati Multistrada 1200/1200S (2015 onwards) and Multistrada 1260, 1260S, 1260 D-Air and 1260 Pikes Peak '18- models.
Extensively used around the world by thousands of road riders, track day enthusiasts, the California Superbike School (USA) and the Chris Walker Race School (UK). R&G’s entire range of Engine Case Covers (ECCs) and Engine Case Cover Kits (KECs) have been approved by the British Superbike Championship (BSB) and the MotoAm...
Left hand side water pump cover to fit the Ducati Multistrada 1200 '10-'14, Streetfighter (1098), 848, 848 Streetfighter, 1098, 1198, Hypermotard 821 / Hyperstrada 821/ '13- and many more.
Made in the U.K.
Extensively used around the world by thousands of road riders, track day enthusiasts, the California Superbike School (USA) and the Chris Walker Race School (UK). R&G’s entire range of Engine Case Covers (ECCs) and Engine Case Cover Kits (KECs) have been approved by the Brit...
This right hand side engine case cover fits the Ducati Multistrada 1200 '10-'14 & Monster 1200 & S '14-.
Made in the U.K.
Extensively used around the world by thousands of road riders, track day enthusiasts, the California Superbike School (USA) and the Chris Walker Race School (UK). R&G’s entire range of Engine Case Covers (ECCs) and Engine Case Cover Kits (KECs) have been approved by the British Superbike Championship (BSB) and the MotoAmerica Series for use in any competitio...
Our industry leading engine case covers are now available in kit form containing all the engine case covers R&G offer for your bike in one go. Developed on track and brought to the road our engine case covers are made from 4mm polypropylene for strength, durability and good looks, they complement our other crash protection perfectly and come approved by the California Superbike School (www.superbikeschool.co.uk).
Suitable for the Suitable for the Ducati Multistrada 1200/1200S 2015...
Suitable for the Ducati Multistrada 1200 and 1200S models '10-'14 Our industry-leading Engine Case Covers are now available in kit form containing all the covers R&G offer for your bike in one go. Developed on track and brought to the road, R&G Engine Case Covers bring BSB and Moto America race series-approved levels of engine protection to your bike for complete peace of mind.
Made in the U.K.
Extensively used around the world by thousands of road riders, track day enthusiasts...
Made from aluminium for excellent strength and crash resistance, its black anodized finish ensures a great looking and long lasting product.
Fits left hand side only.
These bar end protectors have been specially designed and developed for the Ducati Multistrada 1200/S '15-, Multistrada 1200 Enduro '16- and Multistrada 1260, 1260S, 1260 D-Air and 1260 Pikes Peak '18-.
Helping to protect expensive levers and clip ons from damage in the event of a drop, crash or slide.
Easy to install they simply screw into place taking only seconds.
These bar ends are suitable for a range of Ducati and Suzuki models. Click 'more info' to view more specific details.
Kaoko Throttle Stabilizer for Ducati 748/848/916/996/998/999/1098/1198, Streetfighter/S , Multistrada 1200/S '10-, Monster 1100 ABS '10-, SCRAMBLER; Monster 696 '13- & Desert Sled '18-.. Including matching LHS BE in black finish. For Models with 16,8mm ID handle bars. Please check handle bar is 16,8mm ID before ordering.
Kaoko Throttle Stabilizer for Ducati Multistrada 1200/S (2010-) with Barkbusters BLG12 hand guards.
Kaoko Throttle Stabilizer for Ducati Multistrada MTS 1200 (2013) (With Ducati endure Hand guards Part 96793510B).
Kaoko Throttle Stabilizer for Ducati Monster 1200(S)'14/ R '16-,Multistrada 1200/1260/950'17-,Supersport '17/(S) 18-
Awarded RiDE magazine Best buy award status.
R&G Heated grips add months to your motorcycling season and comfort to almost any ride, with easy to install electronics wiring and 5 heat setting adjustments you can optimize the heat output to suit your needs.
Fitting 22mm (7/8 inch) diameter handlebars/clipons and are 124mm (4.9inches) in length long (the most common grip size for sportbikes, enduros, and scooters). In only 2 minutes the grips heat up to 35°C (95°F) and on those r...
based on 1 review
R&G Premium Heated grips add months to your motorcycling season and comfort to almost any ride, with easy to install electronics wiring and 5 heat setting adjustments you can optimize the heat output to suit your needs.
All new Premium Features:
-Heat Setting Memory
-Auto Cut-Out
-Fully Waterproof
-New Grip Design
Fitting 22mm (7/8 inch) diameter handlebars/clipons and are 124mm (4.9inches) in length long (the most common grip size for sportbikes, enduros, and...
Eliminate that annoying spinning grip by getting a tube of grip glue. Holds grips firmly in place. Helps to reduce arm pump caused by trying to hold spinning grips in place.
Ideally suited to be used when installed R&G Heated Grips.
Improve your vision, confidence and safety all year round while you ride!
This ground-breaking product enables you to WASH your visor while on the bike.
Unique wash/wipe action that’s incredibly easy to use: 1. Fill the tank with Visorcat wash (supplied). 2. Wash by moving Visorcat across your visor one way. 3. Wipe the residue away by moving Visorcat across your visor in the other direction. The result is 100% clear vision in all conditions. Keep the sponge clean by rinsing i...
The all-new R&G Second Skin Dashboard Protection kit is made from high quality, anti-scratch material. This bespoke screen protector kit has been designed to protect the delicate dashboard screen on your bike from unwanted scratches and marks.
Kit includes detailed instructions to aid in the dashboard protector placement, 2x dashboard protectors (1x spare), mini spray bottle, suede polishing cloth, wet & dry wipe, squeegee and dust removal strip.
R&G Second Skin stone chip protection film is a non-yellowing (UV Stable), ultra-tough, easy-to-apply, polyurethane protective film. Designed to protect your road or track motorcycle from stone chips, road salt, tar, abrasions, fairing stress fractures and bodywork/fuel tank scratches from general use. The unique properties of our protection film enable it to disperse the impact energy of gravel and small stones, bouncing them off and leaving your bodywork untouched beneath.
Our all-new version of the R&G Brake Lever Guard kit can be fitted to the brake and comes with our universal fitting kit, its expanding design clamps to the inside of the clipon/handlebar (13-21mm diameter) and is available in a range of colour options.
Originally conceived in Moto2 but now adopted by almost every motorcycle body worldwide (ACU, MSVR, MotoAmerica, FIM) and required for racing, the 'Lever Guard' was developed to help avoid the accidental engagement of the front brake/clu...
Originally conceived in Moto2 but now adopted by almost every motorcycle body worldwide (ACU, MSVR, FIM, AMA) and required for racing, the 'Lever Guard' was developed to help avoid the accidental engagement of the front brake lever during close wheel to wheel racing (either from accidental contact with another bike or even a rider) but can equally be applied to road riding, protecting your lever(s) from wing mirror strikes while filters; again potentially causing front brake engagement.
This R&G Moulded Lever Guard kit can be fitted to either the brake or clutch sides and comes with our universal fitting kit, its expanding design clamps to the inside of the clipon/handlebar (13-21mm diameter) and is available in a range of colour options.
Originally conceived in Moto2 but now adopted by almost every motorcycle body worldwide (ACU, MSVR, FIM, AMA) and required for racing, the 'Lever Guard' was developed to help avoid the accidental engagement of the front brake/clutch l...
Easy to install, they help to eliminate damage to the front forks, fork bottoms and brake calipers during a crash or drop.
They help to eliminate damage to the front forks during a drop.
Installing through the rear spindle, they help protect the core (and expensive) rear drive and braking components found around the swingarm area, such as the brake calliper, disc, sprocket and the swingarm itself!
This product covers exposed holes in the rear spindle, nuts and lock pins keeping them clean and free of debris build up.
A silver-finished spacer is complimented by a black cap/cover which has white graphics on it, for a superb looking and finish.
Sold as a kit containing parts for both left and right-hand sides.
This 4 piece R&G Tank Traction Grip kit has been specially designed for the Ducati Multistrada 1200 '15- models.
R&G Tank Traction Grip kits are available for many different bike styles and brands, with new applications released regularly. The unique R&G Tank Traction Grip texture was specifically designed to be both soft and durable, providing the rider with the grip and feel he/she needs to assist in better bike control, enabling the rider to maintain a stable body position while corn...
This Tank Traction Grip Kit has been specially designed for the Ducati Multistrada 1200S/ST '10-'14.
R&G Tank Traction Grip kits are available for many different bike styles and brands, with new applications released regularly. The unique R&G Tank Traction Grip texture was specifically designed to be both soft and durable, providing the rider with the grip and feel he/she needs to assist in better bike control, enabling the rider to maintain a stable body position while cornering and br...
This 3pcs Boot Guard kit has been specially designed for the DDucati Multistrada 1200 / 1200S, Mulitstrada 950 '17- and Multistrada 1260, 1260S, 1260 D-AIR and 1260 Pikes Peak '18- models.
R&G Boot Guard kits are available for a large range of bike styles and brands, with new applications released regularly. The unique R&G texture was specifically designed to be durable, providing the rider with a buffer between his boot on the exposed areas of the swingarm which can (on occasion) come ...
Completely enclosing the motorcycle's rear shock absorber and spring, Shocktube® prevents damage from road salt, water spray, stone chipping, dust and dirt.
Patent No: GB2459728
Should you drop or crash your bike, your end can is likely to be scraped - how ever when an R&G exhaust protector is correctly placed on the exhaust the damage to your exhaust is likely to be greatly reduced.
A large shock absorbing rubber under the protector casing and large enveloped jubilee clip ensure the exhaust protector stays exactly where it should and doesn't damage the exhaust during installation and throughout its life.
Suitable for the Yoshimura R-77 exhaust.
...
Should you drop or crash your bike, your end can is likely to be scraped - how ever when an R&G exhaust protector is correctly placed on the exhaust the damage to your exhaust is likely to be greatly reduced.
A large shock absorbing rubber under the protector casing and large enveloped jubilee clip ensure the exhaust protector stays exactly where it should and doesn't damage the exhaust during installation and throughout its life.
Made in the U.K.
Never forget your sidestand puck again!
Kickstand Shoes bolt onto the bottom of the sidestand, to enlarge the original’s footprint by up to 100%, significantly spreading the load placed upon it, to help prevent the stand ‘piercing’ the ground. Despite this enlargement, the Shoe does not affect ground clearance or interfere with the chain run during normal riding.
This particular model fits the Ducati 1200 Multistrada '10-'14, Ducati Flat Track Pro Scrambler '16-, Ducati Hypermo...
R&G LED Micro Indicators (turn signals) can be used on the front or rear of the bike.
If you are fitting these indicators to an R&G Tail Tidy then you may need R&G indicator adaptors.
In some cases, after fitting these indicators, you may find that they flash too fast or too slow. To stop this, R&G Resistors can be fitted - product code RGR0002 (see related products below) - in some cases more than one resister must be used inline.
Supplied as a pair
The all-new R&G LED Flasher Relay has been designed to fix flash rate problems on indicators.
Please check the existing Indicator Relay for the number of pins on your connector before ordering - if you are still unsure please ask your local dealer.
The all-new R&G LED Flasher Relay has been designed to fix flash rate problems on indicators.
Please check the existing Indicator Relay for the number of pins on your connector before ordering - if you are still unsure please ask your local dealer.
R&G LED Aero Micro Indicators (turn signals) are designed to replicate the shape of our iconic Aero Crash Protector bobbins and can be fitted to the front or rear of your motorbike. Sold in pairs, they come with clear lenses and illuminate on the side for additional visibility.
Available in two colour options: Black or Silver.
Can be used on the front or rear of the bike.
If you are fitting these indicators to an R&G Tail Tidy then you may need R&G indicator adaptors. ...
Filter Results