R&G Racing Products You are viewing an old version of the R&G Racing website
Click here to visit the new R&G Racing website
Alternatively use the following links to jump to a particular section:
Home | Products | New Site Map

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Click rgracing.co.uk/ for Sponsors of Global Motor-Sports.

R&G Racing Products You are viewing an old version of the R&G Racing website
Click here to visit the new R&G Racing website
Alternatively use the following links to jump to a particular section:
Home | Products | New Site Map

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
Fitting instructions for R&G Licence Plate Holder: ZX6-R

FITTING INSTRUCTIONS FOR R&G LICENCE PLATE HANGER

KAWASAKI ZX6-R ‘05 (part code LP0011BK)

 

·          Remove rear seat cover and seat.

·          Remove the two screws at back of bike, on top surface of tail unit.

·          Remove the three push-stop lugs on left hand side which hold rear seat cowl to the undertray (located underneath tail unit, along flanks).

·          Remove side panels.

·          Remove main seat.

·          Remove rear seat cowl (to access wiring loom on left hand side).

·          Unplug number plate light (one red wire & one black/yellow wire).

·          Remove the four nuts holding the tail assembly to the underside of the exhaust – this will allow complete removal of tail unit – go ahead and remove it.

·          Push out sleeve from middle of rubber grommets on OEM tail unit and remove grommets from unit.

·          Locate the R&G hanger and refit grommets and sleeves into four 15mm holes.

·          Fit R&G hanger to underside of exhaust using OEM nuts.

·          Take the wire from the R&G hanger and feed up through (following original wiring path) and reconnect.

·          Test unit for correct operation of indicators and licence plate illuminator.

·          Re-assemble tail unit of bike by reversing the dismantling procedure described above.

The catalogue description and any exhibition of samples are only broad indications of the Products and R & G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R & G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes.
Where R & G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed.  The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products.
On return of any defective Products R & G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R & G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R & G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned.
These terms do not affect the Buyer’s statutory rights.

R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected)
Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary).  Otherwise to be returned to original vendor.
Goods must be in re-sellable condition, in the opinion of R&G Racing
All returns are subject to a 10% restocking and handling fee (10% of the gross value exc. P&P – at the prevailing price at time of purchase)
The customer must pay any and all carriage charges
No returns of discontinued products, unless within 14 days of purchase
This policy does not affect your statutory rights and does not refer to faulty goods
     

 

/ Crash protectors and frame sliders /

Copyright R&G 2002