R&G Racing Products You are viewing an old version of the R&G Racing website
Click here to visit the new R&G Racing website
Alternatively use the following links to jump to a particular section:
Home | Products | New Site Map

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Click rgracing.co.uk/ for Sponsors of Global Motor-Sports.

990 SuperDuke Front, Tops

       

 Please note that the way the kit is packed does not necessarily

represent the way of mounting to the bike

 

FITTING INSTRUCTIONS FOR KTM 990 SuperDuke FRONT TOP CRASH PROTECTORS (CODE CP0153)

 

  • UNDO TOP  FRONT  ENGINE BOLT
  • UNDO REAR BOLT HOLDING “Y” SHAPED BRACKET
  • TAKE  THE R&G ALUMINIUM BLOCK AND ONE OF THE 100MM HEX HEAD BOLTS AND PUT IT THROUGH THE ALUMINIUM BLOCK AND FIT TO FRONT ENGINE MOUNT. TAKE ONE  OF THE 50MM CAP HEAD BOLTS AND PUT THROUGH OTHER END OF BLOCK AND  FIT TO REAR BRACKET TIGHTEN BOTH BOLTS
  • TAKE ONE OF THE 100MM LONG  10MM BOLTS AND SLIDE ONE OF THE 10MM WASHERS UP TO THE HEAD OF THE BOLT
  • TAKE ONE OF  THE BOBBINS  AND PASS THE BOLT THROUGH
  • SCREW THE ASSEMBLY INTO THE ALUMINIUM BLOCK AND TIGHTEN

·         REPEAT THIS PROCEDURE FOR THE OTHER SIDE USING THE OTHER BLOCKS, BOLTS AND BOBBIN

·         DO NOT OVERTIGHTEN – TIGHTEN BOLT UNTIL YOU FEEL COMPRESSION AND THEN MAKE A QUARTER TURN



Due to the risk of cross-threading of bolts etc; we always recommend that our products be fitted by one of our official dealers or a qualified mechanic.
     
Consumer Insert

The catalogue description and any exhibition of samples are only broad indications of the Products and R & G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R & G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes.
Where R & G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products.
On return of any defective Products R & G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R & G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R & G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned.
These terms do not affect the Buyer’s statutory rights.

R&G RACING RETURNS POLICY (NON-FAULTY GOODS)

Returns must be pre-authorised (if not pre-authorised the return will be rejected)
Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor.
Goods must be in re-sellable condition, in the opinion of R&G Racing
All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase)
The customer must pay any and all carriage charges
No returns of discontinued products, unless within 14 days of purchase
This policy does not affect your statutory rights and does not refer to faulty goods
 

<<Back

  
 

All crash protector and frame slider prices include VAT at 17.5%. Postage & Packaging is dependent on weight of total order

Key: S=Set P=Pair E=Each

/ Crash protectors and frame sliders /

Copyright R&G 2002